AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateLennox Ductwork Repair: The Whitney Owner’s Guide
We repair and replace failed Lennox ductwork components in Whitney, and most jobs land between $350 and $1,200 installed depending on whether we’re patching a run, reworking a plenum, or replacing flex and rigid trunk sections behind finished walls. Same-day visits are usually available because duct failures are the most common no-cooling call we run in this town. Most Whitney owners find out something is wrong the same way: a room that won’t cool no matter what the thermostat says, a whine from the attic, or a utility bill that jumped $60 to $90 in one cycle while the system ran longer than it used to.
Which Lennox Models This Applies To
Lennox ductwork isn’t one part. It’s a system of plenums, trunk lines, branch runs, register boots, and transition fittings, and the pieces your system uses depend on the air handler or furnace model inside. The common residential lines we see in Whitney are the Lennox Signature and Elite series air handlers and the Merit series furnaces, but the model number on the cabinet label matters more than the series name. Look inside the unit’s access panel or on the outdoor condenser plate: the model starts with a prefix, then a size code. That size code tells us the airflow rating, and the airflow rating sets the duct diameter. Getting this wrong is the number one compatibility mistake we fix, because a return plenum sized for a 3-ton Lennox will choke a 4-ton system and a tech who eyeballed it will hand you a duct that howls.
The second gotcha is that Lennox has used different plenum heights and coil cabinet dimensions across production years, so a replacement plenum has to match the cabinet, not just the tonnage. We measure the cabinet opening, the plenum height, and the collar spacing before anything gets ordered. For aftermarket, quality flex and rigid duct from established manufacturers meet code and work fine when sized right; OEM matters most for the coil cabinet transition and any factory-engineered plenum piece. We aren’t affiliated with Lennox, and we don’t need to be to get you the right fit. We’re an independent service provider, and that’s why we’ll tell you when aftermarket duct is the smarter buy and when the factory piece is worth the extra.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Signs Your Lennox Ductwork Repair Is Failing
- Whistling or roaring at a register. A sudden hiss usually means a collapsed flex run or a disconnected collar, letting supply air dump into the attic instead of the room. It gets louder as the blower ramps up.
- One room never cools. A crushed or torn branch duct loses a huge share of its air before it reaches the register. In Whitney, we see this most in ranch homes with long attic runs where summer attic temps hit 140 degrees and the flex outer jacket cooks and splits.
- Utility bill climbing with no usage change. Leaking supply duct in a hot attic is money leaving the house. A 20 percent leak in the supply side can add $60 to $90 a month in the cooling season here.
- Dust or attic insulation blowing out of registers. That’s a torn flex jacket or a separated joint pulling attic air into the stream. It also means your filter is doing work it wasn’t designed for.
- Visible tape peeling or mastic cracking at joints. Duct tape fails in attic heat; mastic cracks at the plenum. Both are reparable, but ignored joints widen and eventually pull apart at the collar.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Whitney runs roughly $350 to $650 for a single branch run or collar repair, $650 to $1,200 for a plenum or main trunk rework, and $1,200 to $2,500 for a larger duct replacement in a home with multiple failures and attic access issues. That includes the part, the labor, sealing the joints with mastic and proper foil tape, and a check of static pressure after the work so the airflow is actually corrected and not just patched. What drives the range: attic access and heat, the number of runs involved, whether rigid or flex is right for the location, and whether the plenum needs a cabinet-fit transition. The price we quote is the price you pay. Every duct repair is backed by our 90-Day Done Right Promise in writing, so if it isn’t right, we make it right.
DIY or Call Us?
You can safely do a few things. Look at the registers for dust blowby, check for peeling tape at visible joints, and if you can reach a flex run in cool weather without crawling through a 130-degree attic, a torn outer jacket can sometimes be wrapped. That’s the honest line. Where DIY goes wrong, and where we’ve had to fix the aftermath, is at the plenum and the collar joints: sealing those with the wrong tape or a rushed mastic job can pull loose within a season, and working around a live air handler means electrical and sharp sheet metal in tight space. Please don’t crawl a hot attic in July. Give us a call, and if the repair is simple, we’ll say so. We’ll tell you straight whether a run repair or a full replacement is the square deal for your home. Call (866) 329-8069.
FAQs
Well-installed ductwork should hold up 15 to 25 years, but in Whitney’s attic heat, flex duct jackets often fail at 10 to 15 years because the outer vapor barrier cooks and cracks. Rigid metal duct lasts longer if the joints are sealed properly, which is why we inspect the joints, not just the runs. Call (866) 329-8069 for an honest assessment before you spend on a patch that won’t last.
Yes, in most cases a single failed run, a torn jacket, or a pulled collar can be repaired rather than replaced, and that’s the right answer when the rest of the system is sound. Full replacement makes sense when multiple runs are failing, the trunk is crushed, or the plenum is pulling apart. We quote both options so you can see the difference in writing. A free second opinion on any written estimate is available, and we’ll tell you which one is worth the money.
A single branch repair usually takes one to two hours, and a plenum or trunk rework runs two to four hours on a typical Whitney home. Most of these are completed in a single visit. If attic access is tight or the job spans multiple runs, we’ll tell you up front how long to plan for. The price quoted stays the price paid. Call (866) 329-8069 to schedule.
We match the part to your exact Lennox model number, measured plenum dimensions, and collar spacing, then source the OEM piece or a quality aftermarket equivalent based on what fits and what’s worth the cost. We don’t stock parts or carry them on a truck, so the part is ordered to your system, not pulled off a shelf and made to work. That’s why the fit is right the first time. Call (866) 329-8069 and have your model number handy.
Written by the team at Fireside Heating & Air Co. Whitney, serving Whitney and nearby areas.